Top 10 typical forklift mishaps ， forklift operation ought to focus on these matters ！.

Do not take too lightly the forklift at the workplace. If the operation is not good, there will certainly be serious accidents in minutes, and there are numerous mishaps entailing forklifts.

Case 1: The forklift freight obstructed the driver's sight, and the individual ahead could not be discovered, leading to a moving crash.
Situation 2: In order to preserve the equilibrium of the forklift when raising heavy items, the staff members used their body weight as the counterweight, which almost caused casualties.
Situation 3: The width of the forklift cargo goes beyond the permitted width of the route and hangs on the roadside rack, which virtually creates an mishap.
Case 4: Forklift is speeding and rolls over during a turn.
Instance 5: The forklift driver did not observe the pedestrian, and the pedestrian did not notice the forklift.
Situation 6: The forklift lifts the employees illegally, the forklift motorist does not put on the safety belt, the forklift lifter falls and the chauffeur is crushed when the forklift rolls over.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the lorry when it surrendered and was squashed.
Forklift operation ought to take note of these issues ：.

Beginning.
1. Before beginning, observe the surroundings, and after verifying that there are no barriers that prevent the security of driving, beep the horn first and then start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic pressure (air pressure) gauge need to be risk-free before beginning.
3. When the forklift starts with a load, the driver must initially confirm that the tons is steady and reputable.
4. The start should be sluggish and constant.

Driving.
1. When driving, the height between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole ought to be tilted backward. .
2. Do not raise the fork expensive when driving. When getting in and leaving the job website or while driving, beware that there will be no obstacles overhead. When the lots is traveling, the fork should not be elevated expensive, which will influence the security of the forklift. .
3. After unloading, the fork ought to be decreased to the normal driving setting before driving. .
4. When turning, if there are pedestrians or cars nearby, the driving signal should be released first. High-speed sharp turns are banned. High-speed sharp turns will trigger the vehicle to shed side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it needs to obey the web traffic rules in the factory and need to maintain a particular safety and security distance from the automobile in front. .
7. When the forklift is running, the tons needs to be in the lowest setting that does not impede the driving, and the gantry ought to be appropriately tilted back. The lots shall not be raised except when piling or packing. .
8. The elevation of the tons must not block the driver's sight. In special circumstances, when the thing influences the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the factory area is 5 km/h, and it should drive safely at a low speed when entering the production workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to stand on the fork to hold items and play a balancing role. .
12. If problems are found, they will be fixed and reported in a prompt fashion, and they will never operate with health problems or hide them.

packing and unloading.
1. When fork-loading items, the range in between both forks ought to be adjusted as required to make the tons of both forks well balanced and not manipulated, and one side of the item need to protest the shelf. .
2. It is prohibited to work with a single fork or use a fork top or pull. In special circumstances, safety warning signs should be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading products, the forklift must be braked with the brake. .
4. The rate of the vehicle ought to be slow and consistent. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and Stand-on Electric Pallet Stacker injure people. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork pointer should not touch various other items or things. The tons must be supported with marginal back tilt of the gantry to ensure that the lots does not move in reverse. The mast can be slanted ahead somewhat when the tons is reduced to permit very easy placement of the lots and removal of the forks. .
6. It is restricted to fork items at high speed and ram difficult items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to loaf the fork, so regarding prevent the collapse of the goods and injure people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift employees to engage in high-altitude operations to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should unload the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for special scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be as well sharp to stop the propensity of " totally free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not permitted.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork Electric Forklift Truck for Warehouse is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844